Standing water, damp walls, and musty odors signal hydrostatic pressure building against your foundation -- JCB Waterproofing and Construction stops it at the source.
Here is what sets our basement waterproofing team apart from the rest.
Interior perimeter drains installed by our crew are fully sealed, backfilled with clean aggregate, and protected by a lifetime clog-free warranty that transfers to new owners.
We treat every crack, joint, and tie rod penetration as a potential failure point and address each one individually rather than painting over the problem.
We document every installation with before-and-after photos, moisture readings, and a written record so you have evidence of the work performed and its conditions.
We explain every line item in plain language because customers who understand what they are paying for are the ones who trust us with their second home or rental property later.
Most homeowners in Oregon do not realize that a wet basement is not simply a waterproofing problem -- it is a structural warning sign. Hydrostatic pressure that pushes water through walls does not stop pushing when the water is gone. It continues to stress the concrete and masonry, leading to horizontal cracks in block walls, inward bowing of poured walls, and undermining of the footing system. Addressing the symptom without understanding the root cause means spending money on solutions that fail within a few seasons.
A well-installed interior drain tile system is designed around the specific hydrology of your property. Basements in Oregon that sit in naturally high water table zones require larger-diameter pipe and higher-capacity pumps than basements that only collect surface runoff during heavy storms. Our assessment process measures both the volume and the frequency of water intrusion to right-size every component -- from the pipe diameter to the pump horsepower and battery backup capacity.
In poured concrete walls, the most common seepage points are cold joints, tie rod holes, and form tie locations. These are concentrated, well-defined penetrations that respond well to polyurethane or epoxy injection -- a process of drilling small ports along the crack or joint, installing surface-mounted injection ports, and pumping low-viscosity resin under pressure until it fills the void completely. The cured resin is permanently flexible or rigid depending on the product chosen, creating a watertight seal that moves slightly with seasonal concrete expansion without reopening.
Window wells in below-grade basement windows are a frequently overlooked water entry point. When the well fills with rainwater faster than the soil at the bottom can absorb it, that water presses directly against the window frame -- typically the weakest point in the entire basement envelope. We address window wells with a dedicated drain assembly at the base of the well, tied into the interior perimeter drain system, combined with a properly sized and anchored polycarbonate cover that deflects rain while allowing emergency egress.
A complete basement waterproofing system also requires a reliable, properly maintained sump pump installation. We specify sump pits that are large enough to accommodate both a primary pump and a battery backup pump with sufficient separation that the backup does not interfere with the primary float. Discharge lines are routed to daylight at a point that ensures water flows away from the house and cannot recirculate back to the foundation. Battery backup systems are sized to handle a sustained pumping load during a power outage -- not just a brief test cycle -- because the storm events that knock out power are precisely the events that generate the highest water volume in your basement.
Our full-service waterproofing menu addresses every water entry point from foundation wall to window well.
Our drain tile installations use commercial-grade perforated pipe with filter sock protection, gravel bedding, and a concrete topping restored to match your original floor.
We offer both rigid epoxy injection for structural cracks and flexible polyurethane for non-structural shrinkage cracks, matching the right material to the specific crack type and condition.
We test every installation under simulated load conditions before completing the project, verifying pump cycling, float operation, and battery backup activation before we leave.
The finished surface is coated with a heavy-bodied elastomeric masonry waterproofer that bridges hairline cracks and resists surface moisture transmission year-round.
In cases where floor heaving or settlement accompanies the crack, we supplement injection with a partial slab replacement to restore a flat, properly sealed surface.
Failing or undersized window well flashing and frame seals are replaced as part of every window well drainage project to address all water entry paths simultaneously.
Our assessment includes a history review of your water intrusion events and a visual inspection of the exterior grading, gutters, and downspouts that affect subsurface drainage.
We prepare a detailed written scope covering all materials, methods, and warranty terms before scheduling any work so you know exactly what you are approving.
Our certified crew completes the installation with minimum disruption to your home, working from a phased sequence designed to protect furnishings and maintain basement access throughout.
We perform a complete post-installation inspection, take final moisture readings, and walk you through the system before issuing your written warranty documentation.
We had serious standing water every spring for eight years. JCB Waterproofing and Construction installed a full perimeter drain and sump system and we have been completely dry through two wet seasons since.
The quote was detailed, the crew was on time, and the work was exactly as described. They even patched the concrete so neatly you can barely tell there was a drain trench cut.
Excellent crew, fair price, and the basement has been dry for fourteen months now including one of the wettest summers our area has seen. Highly recommend.
Our Oregon waterproofing team is ready for same-day assessments and emergency response. Call now to schedule your free on-site inspection.
Call +1-866-476-1348 Now